1. Low fluid resistance, the drag coefficient is equal with the same tube section diameter;
2. Reliable sealing, good sealing performance;
3. Fast closing slow opening type, closing speed less than 0.4 seconds, slow opening can prevent the impact on equipment;
4. Convenient repair, the pneumatic ball valve structure is simple, it’s convenient to disassemble and replace the sealing ring;
5. It rotates 90 degrees to open and close the valve, easy to realize automatic control and remote control;
6. The power source of the pneumatic ball valve is gas, the general pressure is 0.4-0.8MPa, safe and reliable. The valve will automatically shut down if the electricity or gas is off.
Technical characteristics:
N8P2 pneumatic ball valve
Information coming soon
1.High precision metal seal structure;
2.Explosion-proof valve;
3.Self cleaning efficiency;
4.Small power consumption;
5.Straight-through, minimum pressure drop, low noise, high flow coefficient;
6.Fast slow type, little impact in pipeline;
7.High security, short closing time, the caliber of the large type valve closed maximum time is 1/30 seconds, a small type valve can be less than 1/60 seconds;
8.No leakage for opening and closing 100000 times, high safety performance;
9.Continuous normal operation for more than 20000 hours.
Advaron N8P2 pneumatic quick cut-off valve, is composed of a single acting spring energy storage reset action actuator and ball valve.
When the valve receives automatic signal valve, the compressed air will go through the filter pressure reducing valve, and then controlled by the electromagnetic valve into the cylinder to push the piston to drive the valve rod to rotate 90 degrees, while compressing the spring to store energy in order to open or close the valve. When the automatic signal change the current valve working state, the electromagnetic valve will shutdown work gas source.
The exhaust gas in the cylinder will vent from the quick exhaust valve, and the spring reset push stem rotates 90 degree to cycle the valve fast closed or open.
The medium for the quick switch valve is water, solvent, acid, oil and natural gas, etc.
N8E1 type electric gate valve:
Pilot-Actuated Safety Valve
Advaron pneumatic quick shutoff ball valves are fast close, slow open ball valves suitable for safety shutoff applications.
Control type: compulsory pilot
Structure: diaphragm lifting structure
Size range: DN100 - DN300
Valve body: ../05../=GS-C25
Cast Steel../08../=1.4581 (AISI 316Ti) Stainless steel
Valve cover: brass (GG25, GS-C25 valve body)
Pressure: 0-25bar
Fluid: neutral, gas or liquid
Fluid temperature: -10 ° /+80 °
Installation: Vertical (must)
Standard voltage: AC:24V 50Hz
Technical performance:
Advaron N8P2 pneumatic quick cut-off valve, is composed of a single acting spring energy storage reset action actuator and ball valve.
When the valve receives automatic signal valve, the compressed air will go through the filter pressure reducing valve, and then controlled by the electromagnetic valve into the cylinder to push the piston to drive the valve rod to rotate 90 degrees, while compressing the spring to store energy in order to open or close the valve. When the automatic signal change the current valve working state, the electromagnetic valve will shutdown work gas source.
The exhaust gas in the cylinder will vent from the quick exhaust valve, and the spring reset push stem rotates 90 degree to cycle the valve fast closed or open.
The medium for the quick switch valve is water, solvent, acid, oil and natural gas, etc.
Technical performance:
Technical characteristics:
1.High precision metal seal structure;
2.Explosion-proof valve;
3.Self cleaning efficiency;
4.Small power consumption;
5.Straight-through, minimum pressure drop, low noise, high flow coefficient;
6.Fast slow type, little impact in pipeline;
7.High security, short closing time, the caliber of the large type valve closed maximum time is 1/30 seconds, a small type valve can be less than 1/60 seconds;
8.No leakage for opening and closing 100000 times, high safety performance;
9.Continuous normal operation for more than 20000 hours.
Characteristics:
- Fail close.
- Fast close slow open – low impact on pipeline.
- 90 degree ball rotation.
- Low fluid resistance.
- Reliable sealing.
- Simple ball valve structure for convenient repair Escribe aquí tu párrafo.
N8P2 pneumatic ball valve
Control mode: Pneumatic actuator
Structure: the rotation of the spool
Valve body: Carbon steel, high temperature resistant cast steel, stainless steel 1.4122, 1.4541, 1.4309
Diameter: DN25-DN300 (1 '' -12 '')
Pressure: 0-25bar
Fluid: neutral, gaseous or liquid fluid
Viscosity: < 600mmmm2/s
Fluid temperature: <250 ℃
Ambient temperature: <60 ℃
Inner parts: Stainless steel 1.4122, 1.4541, 1.4309
Sealing: metal seal, NBR, Strengthened membrane block NBR, FKM, PTFE, EPDM, TecaPeek
Installation: Vertical
Standard voltage: AC:230V, 50/60HZ DC24V
Protection grade: IP55, IP65, EEx DLL CT4, EEx MLL CT4,EEx em, II CT4
Advaron pilot-actuated safety valves are fast close, fast open valves that are actuated by a solenoid.
Characteristics:
- Fast close fast open.
- Low power consumption and control voltage.
- Simple structure.
- Explosion-proof.
- No leakage.
- Compact structure.
N8P2 pneumatic ball valve
Control mode: Pneumatic actuator
Structure: the rotation of the spool
Valve body: Carbon steel, high temperature resistant cast steel, stainless steel 1.4122, 1.4541, 1.4309
Diameter: DN25-DN300 (1 '' -12 '')
Pressure: 0-25bar
Fluid: neutral, gaseous or liquid fluid
Viscosity: < 600mmmm2/s
Fluid temperature: <250 ℃
Ambient temperature: <60 ℃
Inner parts: Stainless steel 1.4122, 1.4541, 1.4309
Sealing: metal seal, NBR, Strengthened membrane block NBR, FKM, PTFE, EPDM, TecaPeek
Installation: Vertical
Standard voltage: AC:230V, 50/60HZ DC24V
Protection grade: IP55, IP65, EEx DLL CT4, EEx MLL CT4,EEx em, II CT4
Technical performance:
Technical characteristics:
Advaron pneumatic quick shutoff butterfly valves are fast close, slow open butterfly valves suitable for conveying a variety of corrosive or non - corrosive fluids.
Characteristics:
- Fast close slow open.
- Good shutoff sealing performance, with elastic seal or metal seal types available. For elastic seal valves, seal rings can be mounted on the body or attached to the valve disc.
- Compact structure.
- Pneumatic actuator can realize remote control and quick opening and closing automation operation.
Pneumatic Gate Valve
Products
Pneumatic Quick Shutoff Ball Valve
Technical characteristics:
Advaron forced pilot quick open, quick closed valve is composed of valve body, valve cover, diaphragm, seals,two position three way electromagnetic valve, check valve and other components. Its working principle is:
When the pressure difference is small in the valve entrance, the valve seat on the valve is still closed by the force ofthe spring, diaphragm and seal, then the two position three way valve connect the valve entrance and upper chamber.
When the valve entrance has medium pressure, leading to the upper chamber, the diaphragm is formed up high and under low differential pressure, which pushes the diaphragm, seals to move downward pressure in the valve closed by valve.
When the two position three-way electromagnetic valve is energized, the system shutoff the valve entrance and passage
in the upper chamber, and connects the upper chamber, check valve and the valve outlet.
Technical performance:
Advaron electric gate valve electric actuators use an involuting curve round of slow open and spring lever energy storage fast closing technology.
The technology does not need auxiliary gas source to drive straight gate valve. The valve plate moves up and down to control fluid on-off in pipeline.
The electric actuator uses spring mechanical reserve force in the shutdown signal or power failure to lift the gate quickly.
The valve will turn into the off state, and the turn-off time is in from 1/30 to 1/60 seconds, and therefore it is suitable for fluid emergency shutdown processing.
The medium of the control valve is gas.
V-Notch Flow Control Valve
Advaron v-notch flow control valves are specially designed ball valves suitable for flow control applications.
The upper chamber pressure decreased rapidly at this time, the pressure difference is formed near the diaphragm and seal, the pressure difference pushes the diaphragm and seal from the valve seat to lift up the valve. When the valve opens, the pressure medium in the upper chamber valve by the export can not reverse into the chamber, so that the valve can not produce fluctuation medium gas pressure changes.The pilot solenoid valve working medium is water, oil, solvent, acid and gas etc.
1. Low power consumption, larger diameter;
2. Simple structure;
3. Low control voltage;
4. Switch quickly;
5. No leakage, good explosion-proof performance;
6. Small volume, compact structure.
Control mode: Pneumatic actuator
Structure: the rotation of the spool
Valve body: Carbon steel, high temperature resistant cast steel, stainless steel 1.4122, 1.4541, 1.4309
Diameter: DN25-DN300 (1 '' -12 '')
Pressure: 0-25bar
Fluid: neutral, gaseous or liquid fluid
Viscosity: < 600mmmm2/s
Fluid temperature: <250 ℃
Ambient temperature: <60 ℃
Inner parts: Stainless steel 1.4122, 1.4541, 1.4309
Sealing: metal seal, NBR, Strengthened membrane block NBR, FKM, PTFE, EPDM, TecaPeek
Installation: Vertical
Standard voltage: AC:230V, 50/60HZ DC24V
Protection grade: IP55, IP65, EEx DLL CT4, EEx MLL CT4,EEx em, II CT4
Pneumatic Butterfly Valve
Advaron © All Rights Reserved.